Friday, October 7, 2022
HomeCamera TechWe Review the Profoto Connect Pro: Should You Upgrade or Not?

We Review the Profoto Connect Pro: Should You Upgrade or Not?

Photo Logo Kit

A couple of years ago, I got a chance to review the Profoto B2 flash with the AirTTL trigger. Although I loved the flash, I had some doubts about the trigger. Now, there is the new Profoto Connect Pro trigger. Is it worth the upgrade?

If you’re using the Profoto flash system, you’re probably familiar with the choices Profoto offers when it comes down to remote triggering. At this moment, there are four different triggers available, each with its own characteristics.

There is the simple Air Remote that works with the X-sync only, but allows you to remotely change flash power. The AirTTL offers TTL measuring and features a simple LCD screen. Some time ago, Profoto announced the Connect, a simple trigger with nothing more than a switch to change from manual to TTL.

Now there is the Connect Pro, a sort of successor to both the Connect as well as the AirTTL. It features something that a lot of photographers who are using the Profoto system were asking about. It offers the ability to read out the flash power directly from the trigger.

The Profoto Connect Pro in Detail

When the Profoto B2 flash came out, the accompanying AirTTL trigger looked somewhat outdated. It felt flimsy, especially compared to the well-built flashes. It could only address three groups of flashes, didn’t show any battery level whatsoever, and most of all, it lacked the ability to read the actual flash power. The only thing you could set was the relative change of power, after which it read zero again.

The Profoto Connect Pro makes up for a lot of the downsides of the AirTTL trigger. Its design is more in line with the Profoto flashes, with the same great built quality and a screen that is similar to the screens found on modern Profoto flashes.

It features four buttons, of which the first three address the flash groups A, B, and C. The fourth button allows you to switch to the next three flash groups, D, E, and F. While the first three groups support TTL, the second three groups are manual only. The Connect Pro has no less than 100 channels available.

The buttons are used to activate a group, after which you can use the dial to change the flash power. It’s also possible to turn a group off by holding a button for a second or two. Or you can press one group two times, after which you are able to change the flash power of all groups at once.

A button in the middle of the dial gives access to the menu. Its design is similar to every other modern Profoto flash. There is a dedicated auto button for switching between manual flash and TTL and a button to activate the model light of the selected flash group(s). A white button on the side of the Connect Pro acts as the power switch and test button.

On the bottom of the Connect Pro, you’ll find the battery compartment, which accepts three AAA batteries. The lid comes off completely, which gives plenty of room to access the compartment. It makes changing batteries easy.

Using the Profoto Connect Pro

Because the interface is similar to every other Profoto flash, using it won’t be any problem for those who are familiar with the Profoto system. It all works the same, with a big and clear screen that offers all the necessary details. It also shows a battery level indicator, so you won’t run into an empty battery without warning, something that happened to the old AirTTL trigger more than once.

The Connect Pro has a range from 0.5-100 meters, although I didn’t check if that claim holds up. This connection is called AirX, which allows communication both ways between flash and trigger. This way, the Connect Pro shows the absolute flash power and is not limited to the relative power change.

For this to work, your Profoto flashes have to be compatible with AirX. And you have to set the protocol of the Connect Pro to Air2. If your flash doesn’t have AirX, like my old Profoto A1 flashes, you can still use these flashes in your light setup, but you’re not able to change any settings whatsoever.

The Connect Pro can also be set to the Air1 protocol. In that case, the trigger works exactly the same way as the AirTTL, with only a relative flash power setting. This way, you have access to the relative power settings of your old flashes again.

Connect With the Profoto App

Just like the modern Profoto flashes, the Connect Pro will also work with the Profoto App. It allows you to remotely change settings on the remote. I know this sounds a bit silly, since you can also change settings of those Profoto flashes directly from the app. But even if you might not see any practical benefit for this, it’s great Profoto added the possibility. You don’t have to use it, but it’s possible, and perhaps in the near future, new functions will give this option a practical use.

The change of settings in the app is transferred by Bluetooth without any delay. The settings can be changed on a flash, on the Connect Pro, or in the app, and the change is taken by every device at once. The only benefit of the app I have found so far is the ability to update firmware. As a matter of fact, you need to use the app for that since the Connect Pro doesn’t have a USB port.


There is not much to add about use in real-life shoots. The Connect Pro works flawlessly. Setting flash power works great when the trigger is set to Air2. You can see the absolute flash power, which makes it much easier to work. There is no need to reach up to a flash high up a flash stand anymore.

Since the interface is similar to every Profoto flash, you can take the Connect Pro from the pouch and use it without ever checking a manual. The buttons feel good.

The only small downside I found is the dial itself. It’s made of a rubber material, and I found the grip not that great, especially when your hands are a bit sweaty. The menu button in the middle of the dial is pressed too easily by accident when you try to rotate the dial. But then again, this is just a minor downside of this otherwise great new trigger.

What I Liked

  • Design and build are up to par 
  • Clear and simple readout on the screen
  • Menu system and interface similar to all other Profoto flashes
  • Readout of the absolute flash power
  • Works similarly to the AirTTL in Air1 setting for older Profoto flashes
  • Six flash groups available, of which three are both manual as well as TTL
  • Has 100 channels available
  • Battery level indicator
  • Works with the Profoto app
  • A nice case is provided

What Still Could Be Improved

  • Battery lid comes off completely
  • Dial has not enough grip, which results in pressing the menu button by accident too often
  • Isn’t able to change settings on non AirX flashes in Air2 setting
  • Price

The Profoto Connect Pro is available for Canon, Nikon, Sony, Fujifilm, Leica, and there is a non-TTL version also. I used the Canon version for this review.

Compared to the AirTTL: Should You Upgrade?

The big question is should you upgrade from the AirTTL trigger? It mostly depends on your own preferences, of course. The build of the Connect Pro is much better compared to the AirTTL. Also, the battery level indicator is a welcome improvement, just like the improved interface. On top of that, you have twice as many flash groups available on the Connect Pro should you need them.

Perhaps the biggest reason for an upgrade is the long-awaited readout of the absolute flash power. If you missed this feature, I would definitely recommend the upgrade. If you’re content with the options of the AirTTL, you might have less reason to upgrade.

s.parentNode.insertBefore(t,s)(window, document,’script’,
fbq(‘init’, 305312604074986);
fbq(‘track’, ‘PageView’);

Read Original Article


Most Popular

%d bloggers like this: